Influence of thickness and initial groove angle in M–K model on limit strain of 7B04 by considering through-thickness stress

Marciniack–Kuczinski (M–K) model is widely used to predict material’s forming limit curve (FLC). The prediction of FLC traditionally neglected through-thickness normal stress. However, it cannot be neglected in some forming processes. Much work has been done to study the effect of through-thickness normal stress on FLC with constant through-thickness normal stress or constant ratio of through-thickness normal stress and maximum principal stress. In addition, based on Nakazima test process, the ratio of through-thickness normal stress and maximum principal stress has been derived, which was a function of instantaneous thickness and loading path. Here, initial groove angle in M–K model was not considered. In this paper, uniaxial tension tests and Nakazima tests were performed on 7B04 aluminum alloy. Based on Hill 48 yield criterion and M–K model, the prediction model of FLC was established. The increase of thickness can enhance FLC. Meanwhile, it is necessary to consider through-thickness normal stress and initial groove angle in prediction model. On the left side of FLC, the effect of initial groove angle on FLC is weakened by increasing sheet thickness. On the right side of FLC, the effect of initial groove angle on FLC is strengthened by increasing sheet thickness. On the right side of FLC, the relation between limit strain points with different thicknesses is linear under one certain loading path. Thickness has decisive effect on through-thickness normal stress level and the changing trendy of through-thickness normal stress during calculation is different under different stress condition.     

涡轮基组合循环发动机分布式控制系统通信网络混合拓扑结构优化方法

涡轮机组合循环(Turbine based combined cycle,TBCC)发动机控制系统通信网络拓扑结构是其分布式控制系统方案设计的重要部分,优化网络拓扑结构可提高发动机推重比和控制系统可靠性。本文基于智能优化算法提出TBCC分布式控制系统网络拓扑结构优化方法。基于图论建立TBCC几何模型和网格模型,以重量和可靠性为优化性能指标,同时考虑发动机表面高温区域以及控制节点的工作可靠性,分别采用粒子群算法和遗传算法优化星形结构中智能中央节点位置、中央节点的环形拓扑结构,获得星形-环形混合拓扑结构。仿真实例表明,基于本文方法优化所得的混合拓扑结构相较于星形集中式控制结构,系统重量降低了51.9%。     

H5飞机调油方法研究

对Ｈ５飞机经过了计算、论证、试飞，在此基础上提出了一种既安全又能充分发挥飞机飞行性能，同时又使动作程序化的调油方法－－规划调油法。用这种调油就可以大大地减少飞行员操纵飞机进的注意力分散，更利于集中精力操纵飞机，以保证飞行的安全。     

Flutter analysis of an airfoil with bounded random parameters in incompressible flow via Gegenbauer polynomial approximation

The effects of parameter uncertainty on the flutter characteristics of a two-dimensional airfoil in an incompressible flow were investigated through Gegenbauer polynomial approximation. The uncertain parameters, such as the linear and cubic pitch stiffness coefficients are modeled as bounded random variables with λ-PDFs (probability density functions). With the aid of Gegenbauer polynomial approximation, the two-dimensional stochastic airfoil system is transformed at first into its equivalent deterministic one. Then the Hopf-bifurcation point is determined through the equivalent deterministic system, and the onset of the flutter, together with the flutter frequency against the probability density distribution parameter and the intensity of the random variable is explored. In addition, the ranges of the peak pitch and plunge responses against the flight speed and the PDFs of the peak pitch response are obtained. Numerical results show how the probability density distribution parameters and the intensities of random parameters affect the flutter onset speed, flutter angular frequency, the upper and lower boundaries of peak responses, and the PDFs of peak responses.     

飞机主操纵系统疲劳试验载荷谱小操纵位移频次问题研究

针对飞机全机主操纵系统疲劳试验载荷谱中小操纵位移频次影响问题进行了分析和讨论,确定了某机全机主操纵系统小操纵位移频次的级别。同时,在原某机全机主操纵系统疲劳试验载荷谱的基础上再次对其小操纵位移频次进行了计算,去掉了这一级别以下对全机主操纵系统疲劳试验无影响的小操纵位移频次,从而完善了主操纵系统疲劳试验载荷谱。另外,对小操纵位移频次问题研究结果在其全机主操纵系统疲劳试验中的实施效果进行了阐述。     

中心极限定理用于近似计算时必须注意的问题

本文着重指出,在运用中心极限定理近似计算独立同泊松分布随机变量之和的概率时,通常只注意了取n适当大的值,从而导致了差异较大的不同结果。本文指出了不仅要使n适当的大,而且也要使nλ足够地大。当X_h是其他离散型随机变量时,也要考虑类似的问题。     

某直升机主桨叶翼型改进后经典颤振分析

直升机经典颤振分析是研究刚性桨叶的最低阶挥舞模态与最低阶扭转模态的耦合不稳定性。经过直升机的理论研究与实验研究,已经形成了一套工程上实用的计算方法。这套方法是建立在金属铰接式旋翼之上。本文计算分析了某型机旋翼主桨叶翼型由NACA0012改进为TSAGI 12.XX翼型后旋翼的经典颤振。     

板料应力成形极限判据的有限元分析程序

为了解决在板料成形有限元数值模拟中以依赖于加载路径的应变成形极限为判据所存在的问题,以板料塑性变形时所遵循的应力应变转换关系、H ill二次厚向异性准则为计算模型,基于有限元商用分析软件DYNAFORM,开发了用于板料塑性成形工艺的以应力成形极限为判据的有限元分析程序。利用该程序分析了两种拉深件的有限元数值模拟结果,实现了用应力成形极限图作为判据对板料成形极限的预测分析。所开发的以应力成形极限作为判据的有限元分析程序为分析多道次板成形的成形极限提供了新的手段。     

一种新的群签名方案

目前大部分的群签名方案中,群公钥的长度和群成员数至少是线性关系,因此在群成员很多时,这类群签名方案很难适用。本文提出一种从代理签名演化而来的新的群签名方案,能够解决这一问题,并且本方案所采用的循环群的阶为一公开参数,群公钥长度固定。     

适用于含多个隐式极限状态方程的飞机结构系统安全分析新方法

工程复杂随机结构的概率安全分析中，最重要的两个步骤是建立所有失效模式的极限状态方程和计算所建立极限状态方程的失效概率。一般来说大型复杂工程结构的极限状态方程都是隐式的，且当材料参数、结构参数和外载荷等均为随机变量时，极限状态方程均为非线性的，为此文中提出了建立真实复杂结构多模式隐式极限方程的等效方法。该方法对于单个极限状态方程采用在均值点展开成线性项和高次项修正的方式，在概率等效的基础上，建立起原非线性隐式极限状态方程的概率等效线性显式极限状态方程。当结构系统所有极限状态方程都建立了其等效显式线性极限状态方程后，即可利用可得的可靠性分析方法来计算结构系统的等效失效概率。所提方法被用于真实飞机结构翼身连接接头的强度刚度多模式可靠性分析，与迭代响应面法计算结果的对比表明，所提方法具有较高的精度。并且所提方法可以与任何标准有限元程序相结合，而标准有限元程序是当今处理结构力学分析与设计的强有力的工具，文中方法提供了力学分析与概率安全分析相结合的合理连接，其应用前景将是十分广泛的。